I recently switched from ATT DSL to Uverse. I never should have!.. I had great service now same computer no additional apps or programs and what took seconds now takes minutes to hours. One minute ai have good connection and 5 min later horrible. It seems to be ok for 10 minutes after I reset the mo

Are there any distinct advantages for an IPV6 address, or is it perfectly fine to drop IPV6 in favor of IPV4, without consideration for usage conditions and other variables? This is the first time I've had to deal with IPV6 up close.

Hello, I'm brand new UVerse GigaPower user.   The transition to this new service hasn't gone as smoothly as I hoped but I want to try to figure out this most annoying issue for now.   First of all, I'm using all of the default settings on the device provided by AT&T. The Motorola NVG589. On speedtes

Learn what could be causing the website not to load and how to resolve Are websites not loading? Is your browser running a bit sluggish? Having trouble with att.com? Check out the fixes below to resolve things like: Website loading issues Virus issues that may be slowing down your computer The dre

I have recently moved house and transferred my service taking my equiptment with me. At my previous address I had no issues but since being here the gateway seem to reboot itself on a frequent basis. I know the system can reboot itself when there are updates, but this seems too frequent for that. It

Hi there, Have a Tomato router in passthrough mode behind a NVG589. Does anyone have expereince getting IPv6 to work with Tomato?

I have a Note 5 with android 6.0.1. When I connect to a wifi network with IPv6 I get slow speeds. My phone will not pull a IPv6 from the router. I see that the rmnet1 interface has a ATT IPv6 address 2600:: address. When will the note 5 have the ability to pull an IPv6 address and work on wifi with

Hi, I ran an IPv6 tunnel from Hurricane Electric (he.net) for a while with my U-verse account and a 3800 HGV-B. The latest software upgrade (6.9.1.42-plus.tm) seem to block IP protocol 41, and I no longer see traffic from he.net coming into the gateway (and no encapsulated IPv6 packets going out).  

I have 2 netgear access points that are relatively new but have been very reliable until recently.  Now I have to reboot them daily to get wifi working.  I wasn't sure if was because IPv6 was turned on recently by AT&T on the RG's...I have turned it off to see if it makes a difference (Home Network/

If you are experiencing issues with loading certain sites, sites not loading completely, it is recommended to disable IPv6. The following goes over steps for a 2Wire/Pace gateway.   For steps for NVG Gateway, go here.     Thanks ATTJohnCS, AT&T Community Specialist

I would like to access my security system remotely without depending on a third party for address resolution. This is non-trivial using traditional dynamic IPv4 addressing. In theory, the entire justification for IPv6 is to avoid the need for dynamic addresses. AT&T (appears to) assign an IPv6 addre

I had AT&T IPv6 working, now it seems to have broken. The AT&T modem broadband status states IPv6 is unavailable. I created a case for it but it seems to be going no where.

Guys, I'm running a 100Mb dry copper with a RG210-700 and five static IPs. Behind of it I use a pfSense firewall, that handles all the internet traffic.That pfSense has four interfaces:- WAN- LAN- OPT1- OPTsThe WAN has all five static IPs; the LAN a 10.10.10.0/24, OPT1 10.10.88.0/24, and OPT2 10.10.

I've read a bunch of stuff online that seems to indicate that the Pace 5268ac will not pass protocol 41, thus making IPv6 tunnels impossible.  I'm posting here to say - that is untrue.  I have a Pace 5268ac, with a single public DHCP assigned address, working with a HE.net /48 routed subnet.  I'm wr

About two weeks ago, native IPv6 networking stopped working on the RG (5268AC). Everything's turned on. I get addresses assigned. But the RG cannot ping ipv6.google.com with IPv6. Either the firmware is hosed or this network segment has issues. It used to work fine.

I went and tested on the ipv6 page and it says my everything is okay except my firmware. I have the 2wire 3801HGV Gateway Is there a firmware update that I need to get to run ipv6? Or is not available as of right now because I am trying to use it. And help would be greatly appreciated.

Just now I fixed my own problem...for once. If you have a Cisco router behind NVG510 in IP passthrough follow these steps: 1: Go to the gateway broadband status page. There you will find an IPV6 address and a border relay address. 2: The IPV6 address is a /60 so go to http://www.gestioip.net/cgi-bin

I currently have business class AT&T U-Verse service with five static IPv4 addresses. I'm working on some development sites for which it would be helpful to have static IP addresses, although I would need IPv6 addresses as I don't have enough IPv4 addresses to cover everything. Is there a block of s

I'm using uVerse Internet with a Fortinet firewall on my home network.  I'm trying to run dual IPv4/IPv6 at home.I'm a network architect wanting to get more experience with IPv6 since, well IPv4 is almost exhausted. On my Arriss BGW210-700, I see the an IP addressing subnet and prefix but nothing li

Is AT&T planning/working on switching their uverse customers from tunneled/6rd to native IPv6?  If so, any timeline? Thank you.